隨著建筑行業(yè)的發(fā)展，我國出現(xiàn)大量的彩鋼板屋面結構的建筑；像大型的廠房或物流庫房等屋面都是彩鋼板構成的；然而在使用后，彩鋼板屋面滲漏水現(xiàn)象較為普通，已引起關注和重視！那么彩鋼板是如何做防水是個問題，如何做好防水更是個問題！普遍常見漏水部位都是彩鋼板天溝、板縫、釘孔部位等異性部位；那么下面就由小編為大家簡單梳理一下彩鋼瓦異型部位如何有用施工？

With the development of construction industry, there are a large number of buildings with color steel sheet roof structure in China; The roofs of large factories or logistics warehouses are made of color steel plates; However, after use, the phenomenon of water leakage of color steel sheet roof is relatively common, which has attracted attention and attention! So how to do waterproof of color steel plate is a problem, and how to do waterproof is even more a problem! The common water leakage parts are color steel plate gutter, plate seam, nail hole and other heterosexual parts; Now let's briefly comb out how to construct the special-shaped parts of color steel tile by Xiaobian?

雨水口、空調管線、天溝、墻體、風機根部等重 點滲水部位,要鋪貼一層附加層,寬度為300mm;或根據實際需要,對重 點易滲水部位加貼附加層,檐口部位要進行包檐處理。重 點滲水部位的處理方法說明如下:

An additional layer with a width of 300mm shall be paved at key water seepage parts such as rainwater inlet, air conditioning pipeline, gutter, wall and fan root; Or according to the actual needs, additional layers shall be added to the key parts prone to water seepage, and the cornice shall be covered. The treatment methods of key water seepage parts are described as follows:

1、釘孔處

1. Nail hole

釘孔容易生銹,要用密封膠預先處理。

Nail holes are easy to rust and should be pretreated with sealant.

2、墻面與墻體交接部位

2. Junction of wall and wall

需在墻體上開鑿5cmx10cm見方的槽,槽底部壓光,防水層粘貼在上面后,用抗裂砂漿填實;或者直接在墻體上用金屬壓條固定防水層,然后用密封材料對卷材收口部位進行密封處理。

A 5cm × 10cm square groove shall be cut on the wall, the bottom of the groove shall be calendered, the waterproof layer shall be pasted on it, and then filled with anti crack mortar; Or directly fix the waterproof layer with metal strip on the wall, and then seal the closing part of the coiled material with sealing material.

3、屋面柱狀體與屋面板交接部位

3. Junction of roof column and roof slab

此處是鋼結構屋面比較容易滲水的部位之一，需在防水層的上方加焊金屬擋水條或金屬防水板，緩解來自鋼柱上方的沖力；上方卷材部位要用纏繞法施工，使卷材不易脫落；擋水板上方用密封材料進行密封處理。

This is one of the parts where the steel structure roof is prone to water seepage. Metal water retaining strip or metal waterproof board shall be welded above the waterproof layer to alleviate the impulse from above the steel column; The upper coiled material shall be constructed by winding method to prevent the coiled material from falling off; The upper part of the water baffle is sealed with sealing material.

4、屋面天溝部位

4. Roof gutter

金屬屋面天溝滲水情況比較普遍，主要原因為設計流水量不足。在突遇特大暴雨時，雨水量急劇增加卻又無法排出，當雨水量積存高度超過房檐下方墻體高度時，雨水就會從房檐下方內溢。

The water seepage of metal roof gutter is common, and the main reason is the insufficient design water flow. When encountering a severe rainstorm, the amount of rainwater increases sharply but cannot be discharged. When the accumulated height of rainwater exceeds the height of the wall below the eaves, the rainwater will overflow from below the eaves.

解決這一難題的方法，主要有增加排水口和對天溝做防水處理兩種方法。此處只對天溝防水處理法作一說明一步，沿天溝邊沿處切除伸入天溝內的屋面板，然后用50cm寬的白鐵皮對折，再壓成一定角度，角度大約等于屋面板與天溝形成的夾角，把鐵皮的一側插入屋面板的下方，另一側用鉚釘固定在天溝壁上

There are two methods to solve this problem: increasing the drainage outlet and waterproof the gutter. Here, only the gutter waterproof treatment method is described. Cut the roof slab extending into the gutter along the edge of the gutter, then fold it in half with 50cm wide white iron sheet, and then press it into a certain angle. The angle is about equal to the included angle between the roof slab and the gutter. Insert one side of the iron sheet under the roof slab and fix the other side on the gutter wall with rivets